Top 10 3D Printing Heating Extruder

Features:
This extruder set is compatible with Creality Ender 3, Ender 3 Pro and other 3D printers.
Mainly including 2 fans, fan cover, heat block, cooling block, nozzle, throat pipe, connector, cable, tube, etc.
Stainless steel material nozzle throat and high quality resistance whose temperature can up to 260 °C/ 500 °F.
Nozzle and tube connect seamless, prevent material leaking and blocking. Heating tube, 24V 40W.
Durable and good performance, fully assembled, you can install directly, good kit for your 3D printer.

Specifications:
Main Material: Aluminum & Stainless Steel & Brass
Nozzle Size: 0.4mm(Brass)
Heating Tube: 24V 40W
Aluminum Heat Block: 20 mm * 20 mm * 10 mm
Fits For: Compatible with Creality Ender 3, Ender 3 Pro
Package Included: (Nozzle+Fans+Fan Cover+Heat Block+Cooling Block+Throat Pipe+Connector+Cable+Tube,etc)
Operating Temperature Range: -40 ~ +260°C (-40 ~ +500 °F)
Package Size: 13.7 * 11.5 * 7.9cm / 5.4 * 4.5 * 3.1in
Package Weight: 241g / 8.5oz

Package List:
1 * Extruder Kit

Please noted that the pins is clamped with long nose pliers.

Specification:
Material: Aluminum & Stainless Steel & Brass.
Installation type: external thread connection
Nozzle size: 0.4mm
Operating temperature range： -40 ~ +260°C (-40 ~ +500 °F)

Package included:
Hot End Kit(Concluded Capricorn Teflon tube)
3*0.4mm Nozzle
3*Silicon Cover

After-sales guarantee: each defective item can be replacement for free or refund. If any question, please feel free to contact or QA us, we will try our best to service you

Specification
Voltage: 12V
Power: 50W
Heating head size: 6 x 20mm
Heating head material: 304 stainless steel
Line length: 39inch /1M
Line thick: 0.5 mm?2; (The cross section of the copper wire inside the heater is 0.5mm?2;)
Color: as shown in the picture
Working Temperature: < 350="">

Single-end heating tube use instructions:
1.The effective heating part of the single-end heating tube must be kept dry.
2.The electrical joint of the single-ended heating pipe should be placed outside the insulation layer and the heating chamber. The working voltage should not exceed 10% of its rated value, and the casing should be effectively grounded.
3.The working environment of the electric heating element, the temperature is not more than 95 degrees, no explosive, corrosive gas.
4.The electric heating element should be stored in a dry place and should not be damp.

Package listing:
3 x 12V 50W Ceramic Cartridge Heater

Note: The Ender 3 Extruder Head Kit Suitable for Creality Ender 3.
These are original replacement parts for Creality 3D printer Ender 3.
Tip of the nozzle, aluminum heating block, throat pipe (built-in Teflon)
Ender 3 Extruder Hot End Kit, white wire was temperature thermistor, Black wire was heating tube 24V 40W

– Installation type: External thread connection
– Application: Creality 3D printers ender 3
– Nozzle size: 0.4mm
– Cable length: 1.2m
– Heating Tube: 24V 40W
– Operating temperature range: -40~+260°C (-40~+500°F)
– Material: Aluminum+Stainless Steel+Brass – Throat length: 52mm
– Aluminum block size: approx. 20 x 20 x 10mm
Package list:
1 x Aluminum Block
1 x Heating Tube
1 x M6*30mm Throat Pipe (Built-in Teflon)
1 x Thermistor +Brass Sleeve
1x 1.75mm 0.4mm Brass Nozzle
5×1.75mm 0.4mm Brass Nozzle ( as free gift)

Feature:
This great replacement for when the old ceramic tape wears out. It is used for 3D printer nozzle keeping warm.
The heating insulation cotton is made from heat-resistant ceramic fiber.
the product sizes can be customized according to customer needs.
the benefit for keeping the key parts of the 3D printer – heating aluminum block warm, is making the internal temperature flat, saving power,and energy.

Size: 75mm*21*2mm +/-0.2mm;

What You Get:10 x 3d printer heating block cottons;

Safety Guide:
Keep away from small children.
This products are only suitable for 3D printer use indoors.
Please read your use guideline of the 3D printer manual carefully before installing and using it.
<3d printer="" consumable:="" pla="" (190°c-230°c)="" or="" abs="" (230°c-250°c)="">

WARNING!!
3D printer replacement parts, Always shut off power to the circuit before starting installation work.
The surface temperature of the 3D printer might be high, and be careful not to touch the heating element to prevent injury.
3D printer initial operation, Do not run the equipment Unattended state.
When printing with a PLA(190°C-230°C) or ABS(230°C-250°C)consumable, if the temperature sensor and other accessories fail, it may cause high temperature hazards. Do not run the equipment Unattended state.
To ensure the users will use the product safely and properly, Please read your 3D printer manual first and follow the instructions step by step before using the product.
Due to the variety of possible end-uses, it is ultimately the responsibility of the customer to determine a product’s suitability for a particular application.

Description:
– Material: Aluminum+Stainless Steel+Brass
– Installation type: External thread connection
– Application: Creality Ender 3, Ender 3X, Ender 3 Pro
– Nozzle size: 0.4mm
– Thermistor and heater cable length: 1.15M
– Throat pipe length: 27mm
– Aluminum block size: approx. 20 x 20 x 10mm
– Operating temperature range: -40~+260¡ãC (-40~+500¡ãF)

Packing included:
1 x hotend kits

Product Description:
– Material: Aluminum+Stainless Steel+Brass
– Installation type: External thread connection
– Application: Creality Ender 3, Ender 3X, Ender 3 Pro
– Nozzle size: 0.4mm
– Thermistor and heater cable length: 1M
– Throat pipe length: 30mm
– Aluminum block size: approx. 20 x 20 x 10mm
– Operating temperature range: -40~+260°C (-40~+500°F)

Packing List:
1 x Aluminum Block
1 x Heating Tube
1 x 0.4mm Brass Nozzle
1 x M6*30mm Throat Pipe (Built-in Teflon)
1 x Thermistor + Brass Sleeve

Features:
Creality 3D Printer full assembled MK8 extruder set For Ender-3/ Ender-3s/ Ender-3 Pro and other 3D printers.
Mainly including 2 fans, fan covers, heat block, cooling block, nozzle, throat pipe, connector, teflon pipe, heating tube, screws, gaskets, etc.
Stainless steel material nozzle throat and high quality resistance whose temperature can up to 260 °C/ 500 °F
24V high speed fan, lose heat quickly and efficiently; nozzle and tube connect seamless,  prevent material leaking and blocking.
100% brand new and durable and good performance, fully assembled, you can install directly, good kit for your 3D printer.

Specifications:
Material: Aluminum & Stainless Steel & Brass
Installation Type: External Thread Connection
Scope of Application: 3D Printer
Package Included: 2 fans + fan covers + heat block + cooling block + nozzle + throat pipe + connector + teflon pipe + heating tube + screws + gaskets, etc.
Fan: 24V 4010 Blower Fan + 24 V 4010 Cooling Fan
Heating Cable: 1m Long, φ6*2mm, 24V 40W
Nozzle: 0.4mm Size (Brass)
Throat Pipe: M6, 27mm Long ((Built-in 40cm longTeflon)
Aluminum Heat Block Size: 20 mm * 20 mm * 10 mm
Operating Temperature Range: -40 ~ +260°C (-40 ~ +500 °F)
Item Weight: 170g/ 6oz
Package Size: 22 * 10.5 * 7.5cm/ 8.7 * 4.1 * 3in
Package Weight: 253g/ 8.9oz
    
Package List:
1 * Full Assembled Extruder Kit

This hot end is a replica of the newest, popular V6 hotend, this hot end not only allows you to print extremely high temperature materials like PP/ Polycarbonate and Nylons but also eliminates typical hotend meltdown failures associated with other types of hotends.

Features:
1.Hot End 100% original and high quality 3D Printer accessories for Ender 5
2.The Hot End work with different sizes of MK10 nozzle: 0.2mm /0.3mm/0.4mm/0.6mm/0.8mm/1.0mm nozzle
3.MK10 Extruder Hot End Kit, white wire is temperature thermistor, red wire is heating tube 24V 40W

Specifications:
Material: Aluminum & Stainless Steel & Brass
Tip of the nozzle:aluminum heating block
throat pipe (built-in Teflon)
Installation type: external thread connection
Scope of application: 3D printer
Nozzle size: 0.4mm
Throat pipe length: 30mm
Aluminum block size: 20 mm x 20 mm x 10 mm
Operating temperature range： -40 ~ +260°C