Top 4 Dash Asic Miner

*POWER SUPPLY IS NOT INCLUDED*
Bitmain recommends using the APW3++ or APW7 power supply.

AntMiner V9 Specifications:
1. Hash Rate: 4.0 TH/s ±5%
2. Power Consumption: 1027W ±10% (at the wall, with Bitmain PSU, 93% efficiency, 25C ambient temp)
3. Power Efficiency: 0.253 W/GH ±7% (at the wall, with Bitmain PSU, 93% efficiency, 25°C ambient temp)
4. Rated Voltage: 11.60 ~13.00V
5. ASIC Chip: BM1580
6. Dimensions: 301mm(L)*123mm(W)*155mm(H)
7. Cooling: 2x 12038 fans
8. Operating Temperature: 0 °C to 40 °C
9. Network Connection: Ethernet (network cable not included)

Please note the following:
1. Due to the nature of these products, there are higher than normal restocking fees (typically 40%). The restocking fees are typically waived in the event that there is a provable failure within the first 30 days and the warranty has not been voided by overclocking. In the event that you experience a failure, please reach out to the seller immediately so that we can begin troubleshooting with you and/or processing a return.
2. Each AntMiner V9 requires TEN 6-pin PCI-e connectors for 12V DC input (must be very stable power source). There are three hash boards that each require THREE 6-pin PCI-e power connectors and one additional 6-pin PCI-e power connector on the controller. All TEN 6-pin PCI-e power connectors are required. Do not connect more than one PSU to the same hash board to prevent possible damage and instability.
3. Power consumption figures will vary with your PSU’s efficiency, the ambient operating temperature and the accuracy of the power meter.
4. Power supply unit is not included. Bitmain recommends the APW3++ or APW7 power supply for the AntMiner V9.

Scrypt Mining Hash Rate: 504MH/s (±7% is expected).
Compatible Coins: Litecoin and any other Scrypt-based coins.
Power Consumption: 800W (±10%) at the wall.
Noise level: Loud. Not for desk-top use. Sounds like a vacuum.
Chip quantity per unit: 288 x BM1485.
Rated Voltage: 11.60 ~13.00V.
Operating Temperature: 0C to 40C.
Network Connection: Ethernet (cable not included).

Notes:
1. Due to the nature of these products, there are higher than normal restocking fees (typically 40%). The restocking fees are typically waived in the event that there is a provable failure within the first 30 days. In the event that you experience a failure, please reach out to the seller immediately so that we can begin troubleshooting with you and/or processing a return.
2. Each AntMiner L3+ requires NINE 6-pin PCI-e connectors for 12V DC input (must be very stable power supply) There are four hash boards that require two 6-pin PCI-e connectors each and one additional 6-pin PCI-e connector on the controller. All NINE 6-pin PCI-e connectors are required. Do not connect more than one PSU to the same hash board to prevent possible damage and instability.
3. Power consumption figures will vary with your PSU’s efficiency, the ambient operating temperature and the accuracy of the power meter.
4. Power supply unit is NOT included. Bitmain recommends the APW3++ power supply for the AntMiner L3+.
5. AntMiners are LOUD. The L3+ sounds like a vacuum and is not recommended for use within homes. Many people use basements or sheds, but returns due to noise will be subject to the full restocking fee.
Compatible Coins: Any coin based on the Scrypt algorithm. There are many dozen coins, but the most well known is Litecoin.

1. Specs:
(A) Hash rate: 17.0 GH/s ±5%
(B) Power consumption: 970W. Power consumption also depends on your PSU’s efficiency.
(C) Dimensions: 14″ x 5″ x 8″
(D) Hashing algorithm: X11
(E) Compatible Coins: DASH, ADZ, ARC, ATX, BOLI, BOPS, BSC, CANN, CNO, CNT, COXST, CREVA, CRM, DP, ENT, ERY, FAL, GILL, GRN, HCC, HPC, INFX, J-x11, KASH, KURT, LGBTQ, LKC, MAR, MARX, MMM, MND, MUE, OGN, ONX, OZC, PIZZA, PXI, SAND, SEV, SMC, START, TOR, TREAU, UIS-x11, VLTC, XCXT, XVP

2. Due to the nature of these products, there are higher than normal restocking fees (typically 40%). The restocking fees are typically waived in the event that there is a provable failure within the first 30 days and the warranty has not been voided by overclocking. In the event that you experience a failure, please reach out to the seller immediately so that we can begin troubleshooting with you and/or processing a return.

3. *A POWER SUPPLY IS NOT INCLUDED.* The APW3++ PSU is recommended above all other PSUs and works with this device when using regular 110v power or 220v power. One APW3++ PSU can only power a single AntMiner D3.

4. Restocking fees for mining devices are 40%. Fees are typically waived if there is a provable failure within the first 30 days. Overclocking will void all warranties. Reach out to the seller immediately if a failure occurs within 30-days of delivery to begin troubleshooting or processing a return.