The Best Whirlpool Dryer Rack Wgd75hefw

Stack kit for standard and long vent dryer

The 3406107 door switch may need to be replaced if you find that the dryer is not starting, will not shut off, or the door will not close properly. All you need for this repair is a putty knife and a Phillips screwdriver. Pry open the top of the dryer, remove the two screws underneath the lint collector without removing the entire thing, unplug the switch, remove the screws that hold the switch place, take out the old switch, and install the new one by screwing it back into place.

The MV-90 is designed for when the vent path takes a 90 degree turn, such as down through the floor, up through the ceiling, or off to the side. -The MV-90 can handle offsets up to 3 inches from center to center. The more accurately you line up the MV-90 with the vent on the back of your dryer, the better the vent path and the further back you can locate your dryer. Normally, the MV-90 requires 5 1/2 inches of clearance behind the dryer. If an obstruction necessitates you locate the MV-90 at the maximum 3 inch offset, then your dryer will need to sit out an additional 3 inches to allow for a bend radius in the transition duct. -Close vent offsets between dryer and wall vent located on same wall as dryer (Offsets between 6-9 inches): The MV-90 can be coupled directly to a standard 4 inch diameter, adjustable, 90 degree elbow which creates a 9 inch offset. See photo below. If your same wall offset is 6 inches, you can use the MV-90 and an elbow, taking advantage of its ability to handle misalignment up to 3 inches. -Same wall offsets greater than 9 inches: Simply mount the MV-90 directly behind your dryer, plug the 90 degree elbow into the wall vent, and measure for the required length of rigid metal pipe between them. Make sure to measure from where the pipe will stop on the MV-90 to the stop on the male end of the rigid metal pipe. -Close vent offsets between dryer and wall vent located on same wall as dryer (Offsets between 0-3 inches): If your same wall offset is between 0 and 3 inches, then the MV-180 is the product for you.

Description:

349241T Dryer Drum Roller Set
The drum roller holds the drum in place while the drum rotates on the support wheels

Works with most top name brands:

Whirlpool, Roper, Admiral, Maytag, Hardwick, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Amana, Kenmore, KitchenAid, Caloric & Ikea.

Replaces part numbers:

AP3098345, 337089, 3389901, 3397588, 3397590, 340352, 3436, 349241, 349241TVP, 661562, 8170, 8205, AH347627, EA347627, K34-895, PS347627.
GE WE3X89, WE3X82

This set includes:

2 rollers,
4 tri-rings
1 retaining washer.

Please reach out to us if you have a question about compatibility. Comment below in the customer questions and answer section or send us a message on the Seentech storefront. We’re happy to help ensure you select the right part number for your dryer.

Detailed Information:

The 279640 dryer idler pulley, also known as a dryer belt tension pulley wheel, keeps the dryer drive belt under tension as the belt wraps around the dryer drum. This part maintains the right amount of tension for the belt to rotate the drum. Common symptoms of a bad dryer pulley are: does not rotate, no start, squealing noises, the drum rotates intermittently but clunks.

Works with the following models: Whirlpool MGDE400XW, Whirlpool MGDZ600TW, Whirlpool WED8300SW0, Whirlpool WED8300SW1, Whirlpool WED9050XW, Whirlpool WED9150WW, Whirlpool WED9200SQ0, Whirlpool WED9250WL, Whirlpool WED9250WW, Whirlpool WGD8300SW1 and more.

Replaces the following part numbers: 279640, 279640VP, 2958, 3388672, 697692, AP3094197, ER279640, W10468057.

Exact replacement for majority of name brands: Kenmore, Whirlpool, Maytag, KitchenAid, Crosley, Inglis, Admiral, Amana.

Resolves the following issues:
Squeals.
Does not rotate.
Will Not Start.
Drum rotates intermittently but clunks.
Buy today and get your dryer back to working order. Click “Add to Cart” now!

The Whirlpool brand names and logos are the registered trademarks of their respective owners. Any use of the Whirlpool brand name or model designation for this product is made solely for purposes of demonstrating compatibility. This warranty is limited to the original purchaser, and is not transferable to subsequent owners of the product unless sold through an authorized re-seller. DR Quality Products is the only authorized seller.

Replaces the following part numbers:
14210003, 31001026, 31531589, 3389628, 3392665, 3394651, 3399844, 345473, 349533, 53-0186, 53-1080, 53-1528, 53-1589, 53-2671, 660996, 660997, 661561, 693306, 694088, 694416, 694868, 695055, 697388, 8066065, 8210, 99906951, 99989673, 99989674, FSP341241, P46-037, W10127457, W10131364

Works for brands:
Whirlpool, Maytag, Magic Chef, KitchenAid, Roper, Norge, Sears, Kenmore, Admiral, Amana and some other

Fit Models:
1LE5700XKW0, 1LE5920XKW0, 1LG5701XKW0, 1LG5921XKW0, 2LG5701XKW0, 3LE5700XKW0, 3LE5710XKW0, 3LE5710XMW0, 3LE5710XMW1, 3LE5710XMW2, 3LG5701XKW0, 3LG5701XPW0, GEN2000HQ1, GEN2000HZ1, GEQ8858HQ1, GEQ8858HZ1, GLE7900XKW0, GLE7900XMW0, GLE7900XMW1, GLE7900XMW2, GLHE7900W0, LE3000XMW0, LE3000XMW1, LE3000XMW2, LE3000XPW0, LE5530XKW0, LE5530XKW1, LE5530XKW2, LE5530XMW0, LE5530XMW1, LE5530XMW2, LE5530XPW0, LE5600XKW0

Contact Us
If you are not sure if part is correct, ask us in Customer questions & answers section or contact us by visiting the Discount Parts Direct storefront.

Business Wholesale
We are a small local company from Houston, Texas offer discount parts for retail and wholesale. If you need to purchase parts for business , please contact us for lower rates.

Description:

Idler pulley W10837240 maintains correct tension on the drive belt to spin the drum.
A dryer’s idler pulley helps the belt to rotate the drum.

This part works with the following brands:

Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Crosley, Admiral.

Replaces part numbers:

2685044, 3021673, 3387372, 3388674, 4337602, AH11726337, AP5669600, AP5671066, AP5988716, B00EKZB0K0, B0189H5EHE, BQ-UWEP-UWQN, EA11726337, EAP11726337, EAP6883871, EAP7320940, PS11726337, PS6883871, PS7320940, W10118754, W10118756, W10547287, W10547290

The product fits model:

3LWED4800YQ0
3LWED4800YQ1
3LWGD4800YQ0
3LWGD4800YQ2
3LWGD4800YQ3
3LWED4800YQ2
3LWED5500YW1
3LWED5500YW2

What situation might you need to replace a new one?

Squeaking noise
Dryer wouldn’t run
Dryer drum was not spinning
Idler wheel is not spinning

Installation Tips:

Always disconnect your dryer from its power source before beginning any repair. Recommended tools include work gloves and a Phillips head screwdriver. It’s also helpful to clear off some floor space, so you have somewhere to put dryer components during disassembly.

Please reach out to us if you have a question about compatibility. Comment below in the customer questions and answer section or send us a message on the Seentech storefront. We’re happy to help ensure you select the right part number for your dryer.

This 010149 Zero Periscope is specifically designed for use in situations where the dryer Outlet overlaps or is very close to the wall Outlet. The 2 inch by 6 inch smooth aluminum construction telescopes to handle outlets up to 5 inches distance from center to center. The 4 inch diameter draw band collar synchs down over the clothes dryer vent i.e.. The 4 inch diameter crimped fitting slides into most wall ies. Once installed, it needs only 2.5 inches clearance behind the dryer. If your outlets are very close and you need to move the dryer closer to the wall, this vent maintains critical airflow and provides all metal performance. Clothes dryer manufacturers specify “only rigid or flexible metal vent shall be used for exhausting. Do not use plastic or metal foil vent.” installation instructions are included inside each carton. The zero periscope is built in the USA by Builder’s Best, Inc.